日付	コード	仕様	ステータス		仕様説明
2019/6/25	AMS2429E	Plating, Bronze, Nitriding Stop-off, 90Cu - 10Sn	Current	Revised	This specification covers the requirements for electrodeposited bronze plate and subsequent removal
2019/6/25	AMS2474E	Chemical Treatment for Aluminum Alloys, Low Electrical Resistance Coating	Current	Stabilized	This specification establishes the engineering requirements for producing chemical-film coatings on aluminum and aluminum alloys and the properties of such coatings
2019/6/20	AMS4926P	Titanium Alloy, Bars, Wire, and Rings, 5Al - 2.5Sn, Annealed, 110 ksi (758 MPa) Yield Strength	Current	Revised	This specification covers a titanium alloy in the form of bars, wire, flash welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides and 16 in2 (103 cm2) and under in cross-sectional area, and stock of any size for flash welded rings
2019/6/17	AMS3253B	Ethylene Propylene Rubber, Phosphate Ester Resistant, 65 - 75	Current	Stabilized	This specification covers an ethylene propylene elastomer in the form of molded sheet and shapes, color coded purple per ARP1527
2019/6/17	AMS6264M	Steel, Carburizing Grade, Bars, Forgings, and Tubing, 1.2Cr - 3.2Ni - 0.12Mo (0.14 - 0.20C) (9317)	Current	Revised	This specification covers an aircraft quality, low alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
2019/6/17	AMS4764G	Copper Alloy, Brazing Filler Metal, 52.5Cu - 38Mn - 9.5Ni, 1615 to 1700 °F (879 to 927 °C) Solidus-Liquidus Range	Current	Revised	This specification covers a copper alloy in the form of wire, rod, sheet, strip, foil, and powder and a viscous mixture (paste) of powder in a suitable binder.
2019/6/17	AMS4152N	Aluminum Alloy Extrusions, 4.4Cu - 1.5Mg - 0.60Mn (2024-T3), Solution Heat Treated and Cold Worked	Current	Revised	This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing produced with cross sectional area of 32 in2 (206 cm2) maximum.
2019/6/17	AMS3260D	Ethylene-Propylene-Diene (EPDM) Rubber, General Purpose, 45 - 55	Current	Stabilized	This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
2019/6/17	AMS2759/1G	Heat Treatment of Carbon and Low-Alloy Steel Parts, Minimum Tensile Strength Below 220 ksi (1517 MPa)	Current	Revised	This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759. Due to limited hardenability in these materials, there are size limits in this specification.
2019/6/14	AMS3194F	Silicone Rubber Sponge, Closed Cell, Firm, Extreme Low Temperature	Current	Stabilized	This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
2019/6/14	AMS3193F	Silicone Rubber Sponge, Closed Cell, Medium, Extreme Low Temperature	Current	Stabilized	This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
2019/6/14	AMS3195H	Silicone Rubber Sponge, Closed Cell, Medium	Current	Stabilized	This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
2019/6/13	AMS3617F	Polyamide Type 6-6, Plastic Moldings and Extrusions	Current	Stabilized	This specification covers one type of nylon thermoplastic resin in the form of moldings and extrusions.These products have been used typically for parts requiring high strength and resistance to aircraft fuels and lubricants up to 120 degrees C (248 degrees F), but usage is not limited to such applications.
2019/6/11	AMS3220H	Rubber, Synthetic, General Purpose, Fluid Resistant, 55 - 65	Current	Stabilized	This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
2019/6/11	AMS3604A	Heat Resistant Aluminized Paint	Current	Revised	This specification establishes requirements for a heat resistant aluminized organic coating with sufficient corrosion and erosion resistance for the finished substrate.
2019/6/11	AMS4931F	Titanium Alloy Bars, Forgings, and Rings, 6Al - 4V Extra Low Interstitial (ELI), Duplex Annealed, Fracture Toughness	Current	Revised	This specification covers a titanium alloy in the form of bars 6.000 inches (152.40 mm) and under in nominal diameter or least distance between parallel sides, forgings and flash welded rings 6.000 inches (152.40 mm) and under in thickness, and stock for forging and stock for flash welded rings of any size.
2019/6/10	AMSC6183B	Cork and Rubber Composition Sheet; for Aromatic Fuel and Oil Resistant Gaskets	Current	Stabilized	This specification covers vulcanized sheet made of granulated cork uniformly dispersed in a synthetic rubber compound, for use in gaskets where aromatic fuel or oil resistance is required.
2019/6/10	AMS4919J	Titanium Alloy Sheet, Strip, and Plate, 6Al - 2Sn - 4Zr - 2Mo - 0.08Si, Duplex Annealed	Current	Revised	This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2019/6/6	AMS3117A	Primer, Zinc Molybdate	Current	Revised	This specification covers a zinc molybdate primer in the form of a liquid.
2019/6/3	AMS4934H	Titanium Alloy, Extrusions and Flash Welded Rings, 6Al - 4V, Solution Heat Treated and Aged	Current	Revised	This specification covers a titanium alloy in the form of extruded bars, and shapes, flash welded rings up through 3.000 inches (76.20 mm) inclusive, in nominal diameter or least distance between parallel sides, and stock for flash welded rings of any size.
2019/5/31	AMS3374F	Sealing Compound, Aircraft Firewall, Silicone	Current	Revised	This specification covers six types of silicone sealing compounds curing to elastomeric materials.
2019/5/28	AMS6948B	Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes, 4Al - 2.5V -1.5 Fe, Annealed	Current	Revised	This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, drawn shapes 5.000 inches (127.00 mm) and under, and stock for forging or flash welded rings of any size.
2019/5/28	AMS4983G	Titanium Alloy, Forgings, 10V - 2Fe - 3Al, Consumable Electrode Melted, Single-Step Solution Heat Treated and Aged, 180 ksi (1241 MPa) Tensile Strength	Current	Revised	This specification covers a titanium alloy in the form of forgings 1.00 inch (25.4 mm) and under in nominal cross-sectional thickness and of forging stock of any size.
2019/5/28	AMS4984G	Titanium Alloy Forgings, 10V - 2Fe - 3Al, Consumable Electrode Melted, Solution Heat Treated and Aged, 173 ksi (1193 MPa) Tensile Strength	Current	Revised	This specification covers a titanium alloy in the form of forgings 3.000 inches (76.20 mm) and under in nominal cross-sectional thickness and of stock for forging of any size.
2019/5/28	AMS4964C	Titanium Alloy Bars, Wire, Forgings, and Rings, 4.5Al - 3V - 2Fe - 2Mo, Annealed	Current	Revised	This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, and stock for forging or flash welded ring up through 6.000 inches (152.40 mm) in nominal diameter or distance between parallel sides.
2019/5/23	AMS4372A	Aluminum Alloy, Plate, 3.5Cu - 1.0Li - 0.40Mg - 0.35Mn - 0.45Ag - 0.12Zr (2050-T34), Solution Heat Treated and Stress Relieved	Current	Revised	This specification covers an aluminum-lithium alloy in the form of plate 0.500 to 6.500 inches (12.70 to 165.00 mm) in nominal thickness (see 8.5).
2019/5/23	AMS5900C	Steel Bars, Forgings, and Mechanical Tubing, Corrosion Resistant, 14Cr - 2.1Mo - 0.30Cb (Nb) - 1.0V (1.05 - 1.15C), Premium Aircraft Quality for Bearing Applications, Double Vacuum Melted	Current	Revised	This specification covers a premium-aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, and forging stock.
2019/5/23	AMS2451D	Plating, Brush, General Requirements	Current	Revised	This specification and its supplementary slash specifications establish the requirements for electrodeposition of metals by brush plating.
2019/5/17	AMS6940B	Titanium Alloy Bars, Forgings and Forging Stock, 3.0Al - 2.5V, Annealed	Current	Revised	This specification covers a titanium alloy in the form of bars up through 1.000 inch (25.40 mm) in diameter or least distance between parallel sides, inclusive, forgings of thickness up through 1.000 inch (25.40 mm), inclusive, high strength fastener stock up through 1.250 inch (31.75 mm), inclusive, and stock for forging of any size.
2019/5/17	AMS6425E	Steel, Bars, Forgings, and Tubing, 1.4Mn - 1.5Si - 0.30Cr - 1.8Ni - 0.40Mo (0.23 - 0.28C), Consumable Electrode Vacuum Melted	Current	Revised	This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
2019/5/17	AMS6417J	Steel, Bars, Forgings, and Tubing, 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.38 - 0.43C), Consumable Electrode Vacuum Remelted	Current	Revised	This specification covers a premium aircraft-quality, low alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
2019/5/17	AMS5744F	Steel, Corrosion and Heat-Resistant, Bars and Forgings, 15.5Cr - 4.5Ni - 2.9Mo - 0.10N, Consumable Electrode Remelted, Heat Treated, 170 ksi (1172 MPa) Tensile Strength	Current	Revised	This specification covers a corrosion and heat-resistant steel in the form of bars, forgings, and forging stock.
2019/5/17	AMS2480J	Zinc Phosphate Treatment Paint Base	Current	Revised	This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating.
2019/5/16	AMS6419J	Steel, Bars, Forgings, and Tubing, 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.40 - 0.45C), Consumable Electrode Vacuum Remelted	Current	Revised	This specification covers a premium aircraft-quality, low alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
2019/5/16	AMS2628B	Enhanced Ultrasonic Immersion Inspection for Titanium Alloy and other Metal Alloy Billets	Current	Revised	This specification covers procedures for ultrasonic immersion inspection of premium grade wrought titanium and titanium alloy round billet 5 inches (127 mm) and over in nominal diameter (see 8.5). Metal alloy billets other than titanium may be tested to this specification with the use of suitable reference standards.
2019/5/16	AMS2470P	Anodic Treatment of Aluminum Alloys, Chromic Acid Process	Current	Revised	This specification establishes the requirements for anodic coatings on aluminum alloys.
2019/5/16	AMS5525K	Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate, 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, 1800 °F (982 °C) Solution Heat Treated	Current	Revised	This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, and plate 0.0010 inch (0.025 mm) and above in nominal thickness (see 8.6).
2019/5/14	AMS4431	Magnesium Alloy, Direct Chill Strand Cast, 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6), Solution and Precipitation Heat Treated	Current	Issued	This specification covers a magnesium alloy in the form of direct chill strand cast round material up to 9.0 inch diameter and rectangular material up to 10 inch by 27.5 inch cross-section (see 8.4) for the purpose of machine from solid applications (see 8.2.1).
2019/5/14	AMS4534D	Copper-Beryllium Alloy, Bars and Rods, 98Cu - 1.9Be, Solution Heat Treated, Cold Worked, and Precipitation Heat Treated (TH04, formerly HT)	Current	Revised	This specification covers a copper beryllium alloy in the form of bars and rods up to 3.000 inches (76.20 mm), inclusive, in nominal diameter or least distance between parallel sides (see 8.7).
2019/5/14	AMS5376H	Alloy, Corrosion and Heat Resistant, Investment Castings, 30Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N, As Cast	Current	Revised	This specification covers a corrosion and heat-resistant iron alloy in the form of investment castings.
2019/5/14	AMS4150N	Aluminum Alloy, Extrusions and Rings, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6), Solution and Precipitation Heat Treated	Current	Revised	This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash welded rings fabricated from extruded stock, and stock for flash welded rings.
2019/5/10	AMS5044K	Steel, Sheet and Strip, 0.15 Carbon, Maximum, Half Hard Temper	Current	Revised	This specification covers a carbon steel in the form of sheet and strip.
2019/5/10	AMS3204N	Rubber Synthetic, Low-Temperature Resistant, 25 - 35	Current	Revised	This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
2019/5/10	AMS4413B	Aluminum Alloy, Plate, 3.5Cu - 1.0Li - 0.40Mg - 0.35Mn - 0.45Ag - 0.12Zr (2050-T84), Solution Heat Treated, Stress Relieved, and Artificially Aged	Current	Revised	This specification covers an aluminum-lithium alloy in the form of plate 0.500 to 6.500 inch (12.70 to 165.10 mm) inclusive, in thickness (see 8.5).
2019/5/14	AMS4534D	Copper-Beryllium Alloy, Bars and Rods, 98Cu - 1.9Be, Solution Heat Treated, Cold Worked, and Precipitation Heat Treated (TH04, formerly HT)	Current	Revised	This specification covers a copper beryllium alloy in the form of bars and rods up to 3.000 inches (76.20 mm), inclusive, in nominal diameter or least distance between parallel sides (see 8.7).
2019/5/14	AMS5376H	Alloy, Corrosion and Heat Resistant, Investment Castings, 30Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N, As Cast	Current	Revised	This specification covers a corrosion and heat-resistant iron alloy in the form of investment castings.
2019/5/14	AMS4150N	Aluminum Alloy, Extrusions and Rings, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6), Solution and Precipitation Heat Treated	Current	Revised	This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash welded rings fabricated from extruded stock, and stock for flash welded rings.
2019/5/10	AMS5044K	Steel, Sheet and Strip, 0.15 Carbon, Maximum, Half Hard Temper	Current	Revised	This specification covers a carbon steel in the form of sheet and strip.
2019/5/10	AMS3204N	Rubber Synthetic, Low-Temperature Resistant, 25 - 35	Current	Revised	This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
2019/5/10	AMS4413B	Aluminum Alloy, Plate, 3.5Cu - 1.0Li - 0.40Mg - 0.35Mn - 0.45Ag - 0.12Zr (2050-T84), Solution Heat Treated, Stress Relieved, and Artificially Aged	Current	Revised	This specification covers an aluminum-lithium alloy in the form of plate 0.500 to 6.500 inch (12.70 to 165.10 mm) inclusive, in thickness (see 8.5).